Safety Devices

Platinum BLGOC-2400LDR Replacement Loop Board

Traffic signal with mounting post and hardware for model 1603.

All-O-Matic Prime VD-1 loop detector for use with LPR-2.

• Easy to Install and set up with the ULTRAMETER sensitivity display
  
• Fail safe in the event of a loop failure
• Faile secure in the event of power loss
• Compact Design
• Cost Effective
• Energy Efficient

• Range: 30 Feet
• Power: 12V-24V AC or DC
• Relay Contacts: 1A @ 24VDC or 120VAC
• Dimensions: 4in. x 2in. x 1.5in. - 18in. Lead Wire
• Housing: Black PVC - Not water tight

Monitored entrapment protection devices are required to protect all entrapment zones in automated gate applications. Photo‐cells are used as type B1 (non‐contact sensors) devices. Electric edges are used as type B2 (contact sensors) devices.

BEA’s LZR^®-H100 is a LASER-based Time-of-Flight sensor designed for gate and barrier applications.

This solution provides four LASER-based curtains, offering a three dimensional detection zone for accurate object detection. Its detection curtains are highly-configurable and can be set up for activation and presence detection in vehicle sensing applications.

The LZR-H100 is an effective alternative to induction loops and is housed in an IP65 rated enclosure, further ensuring its performance in outdoor environments.

***GREEN PCB (DISCONTINUED) WILL NOT WORK WITH RED PCB***

***RED PCB WILL NOT WORK WITH GREEN PCB (DISCONTINUED)***

• UL325-2018 compliant
• Operating range up to 200 ft. (61 m)
• Operating frequency 915 MHz
• NEMA 4X enclosures

***GREEN PCB (DISCONTINUED) WILL NOT WORK WITH RED PCB***

***RED PCB WILL NOT WORK WITH GREEN PCB (DISCONTINUED)***

• UL325-2018 compliant
• Operating range up to 200 ft. (61 m)
• Operating frequency 915 MHz
• NEMA 4X enclosures

***GREEN PCB (DISCONTINUED) WILL NOT WORK WITH RED PCB***

***RED PCB WILL NOT WORK WITH GREEN PCB (DISCONTINUED)***

• UL325-2018 compliant
• Operating range up to 200 ft. (61 m)
• Operating frequency 915 MHz
• NEMA 4X enclosures

• Thru beam configuration
• Wide sensing angle for increased reliability
• 115 ft. operating range
• NEMA 4X enclosure
• Designed to operate in areas with explosive environments
• NEC Class I, Groups B, C & D, Class II, Groups E, F & G CSA certified, CENELEC certified, EExd IIC
• Copper free aluminum with epoxy finish
• Potentiometer range adjustment to allow for more precise tuning to site
• Thru beam design is not affected by shiny surfaces
• Modulated infrared to reduce the effect of sunlight, fog, rain, dust and dirt
• No focusing lens

• Detection range: 50 feet
• Detection Angle: +/- 5%
• Power Supply: 12-24 VDC 24 VAC (2-3.6 Volt Lithium Batteries for transmitter optional; included)
• Expected Battery Life: 2 years
• Size: 4.4″ (112mm) x 2.05″ (52mm) x 1.3″ (33mm)

• Remote Control - For easy programming of the OWL Microwave Motion & Infrared Presence Sensor

• Kit includes photoeye with hood, reflector with hood, and mounting bracket
• Retroreflective configuration
• 50 ft. operating range
• Sensitivity adjustment
• Wide range operating voltage
• IP66 enclosure

NON-MONITORED

• Kit includes photo-eye with hood, reflector with hood, and mounting bracket
• Retroreflective configuration
• 30 ft. operating range
• Sensitivity adjustment
• Wide range operating voltage
• IP66 enclosure

NON-MONITORED

• Remote Control - For easy programming of the Raven Microwave Motion Sensor

Traditional profile rubber edge is available in Normally Open option or compliant with UL 325 monitored 8.2K or 10K Resistive options. Designed out of a tough thermoplastic rubber, this edge will provide years of service. Mounts to gate with an aluminum channel. 3'

Traditional profile rubber edge is available in Normally Open option or compliant with UL 325 monitored 8.2K or 10K Resistive options. Designed out of a tough thermoplastic rubber, this edge will provide years of service. Mounts to gate with an aluminum channel. 4'